Diy Fishing Rod Rack for Truck Updated

Diy Fishing Rod Rack for Truck

I take a truck and car that I routinely bulldoze on my personal wing fishing trips and guided trips with clients. I worry about the rods out on the h2o when nosotros move to different spots to fish because I don't want to interruption the wing rods. But I don't desire to put them completely away and have to string them support because that takes up a lot of precious angling time, especially with clients (and with a wife that likes to know when I'll be domicile, I accept to maximize my time)! I drive the car often considering it gets meliorate gas mileage than the truck. Luckily, the back seat in my car folds down exposing the body. I can thread the rods through the body upward to the front end of the the car and they travel pretty well. I get scared though threading the rods through the car because the rod tips sometimes catch on the seats or other things and I don't want to break them. On the flip side, I don't desire any gear (duffel bags, chest packs, vests, coolers, etc.) shifting or tipping over during the drive and bully the beginning couple sections of the rod or reel (they're not cheap)! Luckily, information technology hasn't happened nevertheless. And with the back seat downwardly in that location is only room for two of u.s. in the automobile. If I'm fishing with a bigger party then dropping the dorsum seat isn't an choice.

I face like issues with the truck. I definitely don't want the wing rods rattling around in the bed with all the gear. I tin break the rods downward in half and they fit in the back seat, but again, it's not very feasible with more than than two anglers and the rods aren't secured at all.

So, long story brusque, I needed a rack for the wing rods. I know people with potent magnet rod racks and these seem to be super potent. But the strong magnets can scratch and ruin the paint on your vehicle. And then suction cup fly rod racks were my preference. I've seen some commercially available ones that retail for $150 http://www.orvis.com/p/sumo-car-top-rod-rack/3l94 but I've seen some people that take made their own in various means and configurations. After seeing a few DIY (do it yourself) fly rod racks online, I decided to build my own. In the finish I spent about $25 and it took two hours of my time.

MATERIALS:

ii Dual Suction Cup Lifters–Harbor Freight $seven.99 each

http://www.harborfreight.com/dual-cup-suction-lifter-46134.html

one Four Slice Ball Stretch Cord–Harbor Freight $ii.99

http://www.harborfreight.com/4-slice-ball-stretch-string-set-47302.html

2 PVC Snap Tees 1″x three/4″– Lowes $1.69 each

http://www.lowes.com/pd_188230-1815-464131RMC_0__?productId=3371266&Ntt=pvc+snap+tee&pl=ane&currentURL=%3FNtt%3Dpvc%2Bsnap%2Btee&facetInfo=

two PVC Threaded Adapters 3/4″– Lowes $0.38 each

http://world wide web.lowes.com/pd_23856-1815-436007RMC_0__?productId=1067457&Ntt=three%2F4+pvc+threaded+adapter&pl=1&currentURL=%3FNtt%3D3%252F4%2Bpvc%2Bthreaded%2Badapter&facetInfo=

two PVC Tees 3/iv″ — Lowes $0.50 each

http://www.lowes.com/pd_23874-1815-401007RMC_0__?productId=1067661&Ntt=3%2F4+pvc+tee&pl=1&currentURL=%3FNtt%3D3%252F4%2Bpvc%2Btee&facetInfo=

1 PVC Pipage 3/4″ ten 2′ — Lowes $ane.82 (Note: A 5′ piece of PVC 3/4″ is simply $ane.92)

http://www.lowes.com/pd_351144-1814-PVC+04007++0200_0__?productId=3341540&Ntt=iii%2F4+pvc+2&pl=1&currentURL=%3FNtt%3D3%252F4%2Bpvc%2B2&facetInfo=

* 1 Foam Plumbing Pipe Insulation 6′ — Lowes $one.xviii

http://world wide web.lowes.com/pd_24433-1410-P11XB/6_0__?productId=3133245&Ntt=iii%2F4+tube+insulator&pl=1&currentURL=%3FNtt%3D3%252F4%2Btube%2Binsulator&facetInfo=

PVC Pipe Cement — Lowes $4.98

http://world wide web.lowes.com/pd_23467-138-31018L_0__?productId=4750803&Ntt=pvc+piping+cement&Ns=p_product_price|0&pl=1&currentURL=%3FNs%3Dp_product_price%7C0%26Ntt%3Dpvc%2Bpipe%2Bcement%26page%3D1&facetInfo=

* Electrical Tape

* Zip Ties

* (I had these items already so I didn't demand to buy them)

Glue and snap the PVC snap tee correct onto the handle of the suction cup lifter.

Thread the adapter onto the pinnacle of the snap tee (I didn't glue information technology then, theoretically, I can divide the top and bottom half of the rack if needed, or plow the top and bottom pieces in opposite directions to find a flat identify on the vehicle). I cutting a small piece of 3/four″ PVC pipe and glued it inside the adapter. This allows the PVC tee to be attached to the top in the adjacent footstep.

Mucilage and attach the PVC tee.

Cut the 3/four″ PVC piping into equal lengths. Glue them into the PVC tee. I matched the lengths to equal the overall width (or so) of the suction cup lifter.

Cut the foam to length and slip over the top of the PVC. I secured it with zip ties so electric tape.

Run one shock cord through the entire length of the PVC pipe covered by the foam. The ball on the end of the cord volition forestall it from sliding through the piping. Tie a second string to the end of the first. I used a dress hanger to hook the end of the daze string and pull it all the way through the pipe.

Finished product! These have been awesome! They've traveled great all day long moving effectually the river and oasis't ever come loose! The suction cups are rated for 200 lbs. so they're very stiff. I've taken them on many trips to and from the river and moving from spot to spot with goose egg problems. I've also transported rods fastened going 75 mph and no issues. They've at present performed through rain storms and a few cold days with some snow and below freezing temperatures with zero problems.

These piece of work and so great I've congenital them for other people and they love them besides!

One early morning I was headed out to the river and had the rods and racks attached to my truck cruising down the freeway at 75mph. Some other truck passed me going pretty fast. Then they abruptly slowed down and we pulled alongside each other. I looked over to see what was going on and the female person passenger had her phone up and was taking pictures of the racks. I could encounter the male driver looking over studying my handiwork. Later on a few pictures they smiled, waved and sped up. Then I hope they figured out how to make the racks. And if by some small phenomenon those people were you and you lot're now reading this weblog postal service, permit me know! Point of the story is, I've seen a demand for these and this is a fantastic, cheap, DIY option.